- CISCO RIGHT TO USE LICENSE SOFTWARE LICENSE
- CISCO RIGHT TO USE LICENSE SERIAL
- CISCO RIGHT TO USE LICENSE MANUAL
- CISCO RIGHT TO USE LICENSE UPGRADE
- CISCO RIGHT TO USE LICENSE REGISTRATION
Last Communication Attempt: SUCCEEDED on Aug 27 13:58:53 2019 PDT Status: OUT OF COMPLIANCE on Aug 27 13:58:53 2019 PDT
CISCO RIGHT TO USE LICENSE SERIAL
One thing I have run into is the licenses have to be associated with the switch serial number.
CISCO RIGHT TO USE LICENSE REGISTRATION
Registration Expires: Aug 26 13:52:59 2020 PDTĪs you can see, there are a lot of things that must go right for this to work. Initial Registration: SUCCEEDED on Aug 27 13:58:49 2019 PDT You can use "show license status" to check on the progress. Use the 'show license status' command to check the progress and result" in the CLI. You will see "Registration process is in progress. Save the token for use on the switch.įrom enable mode, not configuration mode, enter: Click on the blue diagonal arrow on the right of the token to copy it to the clipboard. Look for Administration:Ĭlick "Create Token". When the page loads you will see 5 sections. Smart licensing requires a "Smart" account before you can activate the license on the switch. ! If contact email address in call-home is configured as smart transport callhome ! If contact email address in call-home is configured as the email address configured in Cisco Smart License Portal will be used as contact email address to send SCH notifications.Ĭontact-email-addr http secure server-identity-check Test(cfg-call-home-profile)#no destination transport-method email Test(cfg-call-home-profile)#destination transport-method http Test(cfg-call-home-profile)#reporting all Test(cfg-call-home)#no http secure server-identity-check Test(config)#license smart transport callhome Sending 5, 100-byte ICMP Echos to 72.163.4.38, timeout is 2 seconds: You must remove if you don't use the management interface after install. The "ip http client" statement must be in the configuration while using the management interface. Test(config)#ip http client source-interface g0/0 Once the switch is installed, the management interface will be down so I added a host outside the Mgmt-vrf Since I am using the management interface I had to use the Mgmt-vrf for the host. I added a host entry since this customer doesn't allow name servers. Smart Licensing uses the "Call-Home" service and must be able to reach. Test(config)#interface GigabitEthernet0/0 If you don't have access to a DHCP server use a valid static IP address. I was connecting to a LAN with a DHCP server so I used DHCP. License boot level network-advantage addon dna-advantage
If you purchased additional add ons such as DNA your boot level command will look like this: Next reload AIR license Level: AIR DNA Advantage Network-advantage Smart License network-advantageĭna-advantage Subscription Smart License None Test#show version (showing just the relevant output)
Test(config)#license boot level network-advantage It works, but you get an Alert on the CSSM portal and you will see this in the output of "show license all"Ĭ9300 48P DNA Advantage (C9300-48 DNA Advantage):Įnter the following to set the license level to network-advantage. If you don't do this, the call-home service will try to register DNA Advantage and Network Advantage licenses. My switches were purchased with network-advantage licensing so I entered the code listed below. You will need this if you contact TAC or the licensing team. This is what Cisco calls the Sales Order (SO) number. Near the bottom is a bar code label "Order #". That is because there were 17 switches on the sales order. Notice in the picture below that the quantity is 17. There will be a printed card in the box with the swiitch that lists the type and quantity of licenses that were purchased. If your switch already has internet access you can skip the management interface configuration. If you are building the switches at your office for a customer you can configure the management interface and use your internal network. You can use a proxy but I am not going to cover that today. It's actually pretty easy but it does require Internet access. So how do you set up Smart Licensing on the switch?
CISCO RIGHT TO USE LICENSE UPGRADE
That means that as soon as you upgrade to 16.9.1 or later your Right to Use licensing will no longer work. "Licenses are managed as smart licenses from Cisco IOS XE Fuji 16.9.1 and later."
The important statement on the website is this statement:
CISCO RIGHT TO USE LICENSE MANUAL
Smart Licensing also enables you to automate time-consuming, manual licensing tasks."
CISCO RIGHT TO USE LICENSE SOFTWARE LICENSE
"Smart Licensing is a cloud-based, software license management solution that allows you to manage and track the status of your license and hardware and software usage trends. According to Cisco Smart Licensing is the future.
0 kommentar(er)
